Xingtai Zhongyao Chemical Co., Ltd. | Established 2016 | magnesium oxide and hydroxide manufacturing, industrial-grade magnesium salts, rubber, cable, flame retardant, environmental, ceramics | September 22, 2026

Key Takeaways

  • Soluble sodium and electrical conductivity drive water treeing, not just particle size.
  • Silane and stearate surface treatment decides whether you hit high loading without embrittlement.
  • A single out-of-spec batch can scrap an entire extrusion run before the cable ever ships.
  • Halogen acid and smoke density compliance are pass/fail gates, not optimization targets.

Where Substandard Mg(OH)2 PVC Batches Break the Line

A 5% water treeing degradation at 12 kV after 72 hours is not a lab curiosity. On a production floor, it is the difference between a passing lot and a scrapped drum of compound. Most plant engineers discover this the hard way, after the cable has already been jacketed.

The root cause usually traces back to one incoming raw material: Mg(OH)2 for PVC Cables. This grade sits at the center of low-smoke-zero-halogen formulations. It is also the most common source of line instability I see in cable plants running flexible PVC and polyolefin jackets.

Here is the problem. Magnesium hydroxide is a mineral filler, and mineral fillers vary. behave completely differently on the extruder. The difference lives in soluble sodium, surface treatment, and conductivity. Those three parameters decide your yield.

This review looks at a specific modified magnesium hydroxide grade built for LSZH cable compounds.I will walk through the technical parameters, the production consequences of each one, and how the grade positions against standard industry baselines.

The criteria are simple: does the powder hold line stability at high loading, and does it pass halogen and smoke gates without rework?

For engineers sourcing the broader family of cable additives, the related Industrial Magnesium Oxide catalog follows the same QC logic.

Product Overview and Positioning

This grade is a high-purity, reactive modified magnesium hydroxide powder. It is engineered specifically for LSZH cable compounds, with an ultra-fine D50 of 1.2 µm. That particle size is not cosmetic. It is what enables 65-70 wt% loading in flexible cables without destroying mechanical properties.

The surface modification is the second positioning pillar. The powder carries a silane and stearate treatment. That treatment does two jobs. It reduces agglomeration during compounding, and it improves interfacial bonding between the mineral and the polymer matrix.

Purity sits at ≥ 99% Mg(OH)2 content. Soluble sodium is capped at ≤ 0.01%, and electrical conductivity is rated low. Those two numbers matter more than most engineers expect. Sodium ions migrate under electrical stress and seed water trees. Low conductivity keeps the compound stable in wet service.

The grade is certified to ISO 9001:2015 and positioned for halogen-free cable jackets. It targets the flexible cable segment, where high filler loading is mandatory for fire performance but punishing on elongation.

Why Particle Size Distribution Controls Loading

A D50 of 1.2 µm with a tight distribution does more than improve dispersion. It lets you push filler content to 65-70 wt% while keeping the compound extrudable. Coarse or broad distributions force you to cut loading, which drops flame performance below spec.

The Role of Surface Treatment

Untreated magnesium hydroxide absorbs moisture and clumps. Silane and stearate modification changes the surface energy, so the particles wet out into the polymer. The result is fewer die-drool events and more consistent melt flow across a long run.

Technical Parameters Deep Dive

Every parameter on this datasheet maps to a line outcome. I will go through each one and state the production consequence directly.

Parameter Value Unit Production Consequence
Mg(OH)2 content ≥ 99 % Higher active content means less inert filler per kilo
Soluble sodium ≤ 0.01 % Controls water treeing and insulation resistance drift
Electrical conductivity Low — Prevents ion migration under wet electrical stress
D50 1.2 µm Enables 65-70 wt% loading without embrittlement
Water treeing resistance 72h @ 12 kV, <5% degradation — Predicts field life in wet or buried service
Smoke density <50 — IEC 61034 gate, >60% light transmission
Halogen acid <0.5 % IEC 60754-1, zero corrosive gas release

Start with soluble sodium. At ≤ 0.01%, the powder limits the free ions that migrate toward the conductor under voltage. High sodium content shows up as rising leakage current and premature water tree formation. If your incoming COA reads above spec, reject the lot before it reaches the mixer.

Electrical conductivity follows the same logic. A low rating keeps the compound’s dielectric behavior stable over thousands of operating hours. This is not a parameter you can compensate for downstream.

The D50 of 1.2 µm is the loading enabler. At 65-70 wt% filler, a flexible cable compound is already near its mechanical limit. Coarser powder raises viscosity and forces you to reduce loading, which weakens flame retardancy. The ultra-fine fraction keeps the melt flowing.

Water treeing resistance is the field-life predictor. The grade holds degradation below 5% after 72 hours at 12 kV. Water trees grow from ionic contaminants and voids, so this result ties directly back to sodium control and dispersion quality.

Smoke density sits below 50, which corresponds to more than 60% light transmission under IEC 61034. Halogen acid stays under 0.5% per IEC 60754-1, meaning zero corrosive gas release. Both are pass/fail gates in LSZH certification. Miss either one and the lot is dead.

For formulators also working with polyolefin systems, the High-purity MDH flame retardant range uses the same surface-treatment chemistry.

Reading a COA Like a Line Engineer

Check soluble sodium, conductivity, and moisture first. Those three predict extrusion behavior better than particle size alone. A tight D50 with loose sodium control still fails in wet service.

Moisture and Storage Effects

Modified powder still picks up ambient moisture if bags sit open. Damp feed causes steam voids in the melt and surface defects on the jacket. Keep bags sealed and rotate stock so nothing sits for months.

Performance and Industry Comparison

The comparison that matters is against the baseline grades most plants already run. Standard, untreated magnesium hydroxide typically tops out at lower loading. Push it higher and elongation collapses, which forces a compromise between fire performance and flexibility.

This grade changes that trade-off. At 65-70 wt% loading, the treated powder maintains mechanical integrity because the silane and stearate layer keeps the polymer-mineral interface intact. Untreated powder at the same loading turns brittle.

Metric This Grade Standard Untreated Mg(OH)2
Max loading in flexible cable 65-70 wt% Lower, elongation-limited
Surface treatment Silane + stearate None
Water treeing, 72h @ 12 kV <5% degradation Higher drift
Soluble sodium ≤ 0.01% Variable by source
Smoke density <50 Grade-dependent
Halogen acid <0.5% Grade-dependent

The smoke and halogen columns are where untreated grades get exposed. Without tight sodium and conductivity control, smoke density climbs and the compound fails IEC 61034. That is a full-lot scrap, not a tweak.

On yield, the difference compounds fast. A batch that extrudes clean at 65-70 wt% loading runs at full line speed. A batch that forces you down to lower loading or causes die-drool runs slower and generates more off-spec jacket. Scrap rate, not raw material price, decides which grade is cheaper.

The same QC discipline applies across adjacent product lines.Plants running rubber sheathing often pair this with [Active Magnesium Oxide](https://zhongyaochemical.

com/products/active-magnesium-oxide) for vulcanization control, and tire lines use MgO for Tires for sidewall performance.

Line Stability at High Loading

High filler loading raises melt viscosity and torque. The ultra-fine D50 keeps that rise manageable. When torque stays inside the window, you avoid surging and the jacket thickness holds tolerance.

Scrap Rate Drivers

The three biggest scrap drivers with this class of filler are moisture voids, die-drool from poor dispersion, and failed smoke or halogen tests. All three trace back to incoming QC. Control sodium, conductivity, and moisture, and scrap drops.

Frequently Asked Questions (FAQ)

Does D50 alone predict extrusion performance? No. Soluble sodium, conductivity, and moisture predict line behavior more reliably than particle size by itself.

Why does soluble sodium matter at 0.01%? Sodium ions migrate under electrical stress and seed water trees, which shortens wet-service cable life.

Can untreated Mg(OH)2 hit 65-70 wt% loading? Rarely. Untreated powder embrittles the compound at high loading, forcing a lower filler content and weaker flame performance.

What fails an LSZH lot first? Smoke density and halogen acid. Either one above the IEC gate scraps the entire batch. Is water treeing a lab-only concern? No. It predicts field life in buried and wet installations, so it belongs in incoming QC.

How should powder be stored? Keep bags sealed and rotate stock. Moisture pickup causes steam voids and jacket surface defects.

Conclusion

Score this grade on the parameters that hit the line, not the marketing sheet.Soluble sodium at ≤ 0.01%, low conductivity, and a **1.

2 µm** D50 together deliver 65-70 wt% loading with water treeing held under 5% after 72 hours at 12 kV.Smoke density below 50 and halogen acid under 0.5% clear the LSZH gates.

Overall score: 9/10. The grade earns it on tight sodium control, proven loading capacity, and clean compliance margins. The one point off goes to storage sensitivity, which demands disciplined inventory rotation.

For production engineers, the recommendation is direct.Run incoming QC on sodium, conductivity, and moisture before the mixer, not after the extruder.That single change protects yield, cuts scrap, and keeps the line stable at full loading.

Xingtai Zhongyao Chemical Co., Ltd.has manufactured industrial-grade magnesium salts from Hebei’s magnesite belt since 2016, with an integrated chain from ore mining to ultra-fine milling.